3 WAY DIMMER FOR LED LIGHTS INSTALL

Two Red wires: These wires attach to the 'travelers' which are the pair of wires attached to the two screws at one end of the regular 3-way-switch.

Green wire: Attach to the bonded ground wire(s) in the switch box. Wiring a Standard 3-Way Dimmer SwitchДЈ-Way Dimmer Switches typically come with the following pre-wired leads Some fixtures allow you to use regular dimmers, however some do not. Regular 3-way dimmer switches are designed for incandescent lamps unless otherwise stated.Д¬onsult the instruction sheet that accompanies the low voltage lighting fixture for the correct dimmer to use. If you do not size your dimmer properly the dimmer could overheat and cause internal damage. Residential dimmer switches are available for several load requirements including 600, 8 watts.

Check to make sure your lamp or light fixture is compatible with your dimmer switch.

Check to make sure your dimmer switch is compatible with your lamp or light fixture.

Residential Dimmer Switches used for several types of lighting fixtures.Дimmer Switch and Light Fixture Compatibility.

Which are are compatible and work well together. Newer specially designed fluorescent fixtures and dimmers are available Lamps to over heat and burn out prematurely. That is not rated for dimming or a fixture which has CFL - CompactДimming non-compatible fixtures or lamps will cause the fluorescent Never wire a regular dimmer to an older fluorescent light fixture Never exceed 80% of the rated load for any electrical component The total watts which will be controlled by your 3-way dimmer switch.ДЄ good rule of thumb with any electrical load calculation is to The number of lamps per fixture and the watts per lamp. You have several light fixtures which will be controlled by theДЈ-way dimmer switch you will need to count the number of fixtures, Most dimmers are rated for 600 watts of power consumption, so if Will have you cap off one of the wires which will not be used.Д¬are should be taken in selecting your dimmer switch. For the Single Pole application the instruction sheet Many manufacturers are now producing dimmer switches that can be used for either Single Pole or 3-Way To your notes to help you wire the new 3-way dimmer switch. Switch is wired BEFORE you remove the wiring, then refer When replacing an existing 3-way switch take note of how the existing If you are replacing an existing 3-way switch: These dimmers are also known as wall dimmers Most 3-Way dimmers come with pre-wired leads that are color codedДЄnd explained below. Remote control distance: about 8-15meters indoor, over 30m outdoor.A 3-way dimmer switch is very similar to a regular 3-way toggle switchД®xcept for the electronic unit which performs the actual dimming

Inductive load: maximum output power of single set is within 360W(like light with ballast: energy saving light, bracket lamp, absorb dome light) Resistive load: maximum output power of single set is within 1000W(such as common incandescent light bulb, the light bulb)

3 WAY DIMMER FOR LED LIGHTS INSTALL

Great use in house, stairs, aisle, toilet, warehouse, factory and so on.ДЎ.In the case of electromagnetic and high frequency interference, the effective remote control distance will be shortened or failure but eliminate interference can return to normal.Дў.Do not open the product in the case of power on with the high voltage inside the switchДЈ.Before using the item, please read the instructions on the receiver carefully, and ask a qualified electrician to install which can avoid installation errors or damage to electrical appliancesД¤.Far away from the product electromagnetic inductance or sub-class products, straighten antenna and do not wrap the receiver, so as not to affect the signal reception when installing the receiver.ДҐ.Please replace the battery when the remote indicator is dark ,RC distance shorter and sensitivity drops.Д¦.Arrange the electrical load properly within the corresponding switching capacityДў.A/1 uses to turn on /off the blue group, B/2 uses to turn on /off the white group, C/2 uses to turn on /off the yellow group,'ON'/'OFF' means turn on/off the whole item.ДЈ.Manual lighting sequence (wall switch control): A/1, B/2, C/3, the whole circuit will be turned on. Suitable for some electric appliance like droplight, crystal lamp, frame lamp, Long working life up to 1 year with the capability of penetrating walls and anti-disturbance.Д®quipped with high load relay, high voltage capacitor and high quality receiver. Easy to operate which can fully turn on or turn off the whole circuit.Д«ilateral control with remote controller and wall switch control.

3 way dimmer for led lights